How to Fix Power Steering Pump

If you’re like most drivers, you’ve probably experienced a power steering pump fail at some point in your life. Whether it was due to a clogged filter or worn parts, a power steering pump failure can be quite frustrating. Here are four tips on how to fix a power steering pump failure.

What is a Power Steering Pump?

A power steering pump is a device that helps circulate the engine’s fluid, which is used to turn the wheels of a car or truck. When the pump malfunctions, it can cause a lot of problems, such as loss of power and difficulty steering.

How do I Fix a Power Steering Pump?


There are several ways to fix a power steering pump, depending on the cause. If the pump is defective, you may need to replace it. If the pump is leaking or has clogged filters, you may be able to fix the issue by replacing the seal and filters. If the pump is just not working right, you may be able to temporarily fix it by changing the belt or pulley.

How do Power Steering Pumps Work?

Power steering pumps are used to circulate the fluid in the system that helps make the car move. This fluid is typically a type of oil, but can also be water or other types of fluid. The pump works by using a motor to turn a shaft and create motion. This motion then causes the pump to push and pull the fluid through the system.


There are a few ways to fix a power steering pump if it is not working properly. The first is to check for any leaks in the system. If there are no leaks, then the next step is to try and replace the pump. If replacing the pump does not work, then you may need to replace the entire system.

If you are not sure how to fix power steering pump, or if it is not working properly, then you should consult a professional mechanic.

When do Power Steering Pumps Fail?

Power steering pumps are a critical part of your car’s engine, and when they fail, you can experience a lot of trouble.

How to Fix a Power Steering Pump – The Basics

If your car starts to pull to one side when you apply power steering, there is a good chance that your power steering pump is going bad. Here are the basics on how to fix a power steering pump:

See also  Can I Drive Without Power Steering Fluid

1. Make sure the car is level. This will help to ensure that the pump is getting the same amount of pressure in all directions.
2. Check for leaks. If there are any leaks, they can cause the car to pull to one side. Fix any leaks before proceeding.
3. Remove the power steering pump pulley and bolts. Use a wrench to remove the bolts and then set them aside in a safe place.
4. Remove the power steering pump by turning it counterclockwise with a wrench. You may need to remove the intake manifold as well in order to get access to the pump.
5. Inspect the impeller and bearing for wear or damage. If either of these are present, replace them as needed.
6. Replace the power steering pump if necessary and reattach it using new bolts and pulley. Tighten them down in a clockwise direction until they’re snug, then check for leaks again before driving the car.

Fixing a Power Steering Pump – Advanced Techniques

When your power steering pump goes out, it can cause a whole lot of problems. In this article, we will cover some advanced techniques for fixing a power steering pump.

If you have access to a vice, you can replace the power steering pump without removing the entire steering column. To do this, remove the four bolts that hold the steering column in place, then tilt and pull the column out of the car.

If you don’t have access to a vice, or if you want to replace the pump without removing the entire column, you will need to remove the rack and pinion gear assembly. To do this, remove the four bolts that hold it in place and then pull it out of the car.

Once you have removed the gear assembly, you can access the power steering pump. To replace it, take note of which size pump your car is using (the newer pumps are usually a little larger) and then unscrew the old one from the bracket.

Insert the new pump into the bracket and screw it together. Be sure to torque the pump down to manufacturer specifications – usually around 30 ft-lbs.

DynoCar is the best place to find information on all things cars, whether it be a car buying guide or how to change your oil. We’ve made finding and staying in touch with car information easy and fast.

Resources

Guides

About Us

Contact

Contact

DynoCar - All About Cars

(440) 999 3699

590 Monterey Blvd San Francisco, CA 94127

Information contained herein is for informational purposes only, and that you should consult with a qualified mechanic or other professional to verify the accuracy of any information. DynoCar.org shall not be liable for any informational error or for any action taken in reliance on information contained herein.