When you’re out and about with your little one, it can be hard to find a place to put them down while you do some shopping or run an errand. That’s where a Graco car seat comes in handy. But what if you don’t have a city select stroller? Won’t the Graco car seat just fall off? Not necessarily. In this blog post, we will show you how to attach a Graco car seat to a standard city select stroller. This is a great way to use the car seat when you don’t have access to a city select stroller or when you want to take it with you on the go.
Preparation
attaching a graco car seat to a city select stroller is easy peasy
1. open the city select stroller and remove the seat liner.
2. locating the clip that attaches the car seat to the stroller, insert it into the groove on the bottom of the seat liner.
3. reattach the front panel of the car seat to the front of the liner by pressing down firmly. The straps should now be inside out.
4. reattach the back panel of car seat to back of liner by pressing down firmly (the straps should now be outside in). Voila! You’re done!
Attaching the Graco Car Seat
If you have a Graco car seat, you may want to attach it to your city select stroller for easy transport. To attach the car seat, first make sure your stroller has a second seat. The car seat should snap in place on the right side of the stroller.
Removing the Graco Car Seat
The Graco car seat is a great option for children who are not yet ready to ride in a stroller. The car seat can be attached directly to the city select fold-up stroller. There are several different ways to attach the car seat to the stroller, and each method will depend on the model of stroller and the car seat.
To attach the car seat to a Graco city select fold-up stroller, first remove the shoulder straps from the car seat. Next, thread one of the strap adjusters through one of the belt loops on the side of the stroller. Pull up on the adjuster until it locks into place. Repeat this step on the other side of the belt loop.
Now, connect one of the waist belt adjusters to one of the shoulder belt loops on the car seat. Push down on both adjusters until they click into place. Finally, connect one of the child’s arms through one ofthe child safety clips on either side ofthe carseat and clip it in place.
Turning the City Select Stroller Into a Travel System
When it comes to taking your little one on the go, nothing is more convenient than a quality city select stroller. However, if you’re like most parents, you don’t want to lug around a huge carseat and an infant carrier every time you need to take your baby out.
Fortunately, there’s an easy solution: turn your city select stroller into a travel system! By following these simple steps, you can easily attach your Graco car seat to the stroller frame, making trips around town much easier and more comfortable for both you and your kiddo.
1. Locate the attachment points on the stroller chassis. There are several different locations where you can secure your Graco car seat, but four of the most common spots are near the front wheel wells (pictured above), at either side of the seatback, and beneath each armrest.
2. Make sure that your carseat is properly inflated before attaching it to the stroller. The pressure applied by the frame will ensure that the straps stay attached while you’re on the go.
3. Insert one end of each strap through one of the attachment points on your carseat, then thread each strap through each of its respective holder on the frame of the stroller ( pictured below ). Be sure to tighten all four straps firmly in order to ensure a securely attached system!
4. Repeat steps 2-3 for the other end of each strap
Conclusion
If you’re looking to attach your Graco car seat to your city select stroller, follow these simple steps: 1. Locate the two attachment points on the back of the car seat. 2. Use a screwdriver or similar tool to loosen the locknuts on each attachment point. be careful not to overtighten them as this could cause damage to the car seat or stroller. 3. Tighten each locknut by turning it clockwise until it is snugged against the car seat and/or stroller frame (but do not over-tighten!). 4. Reconnect any straps that were removed in step 2, if necessary, and adjust them as needed.