If you own a car, you’ve probably experienced the frustration of having to change your ignition switch. It can be a hassle, and it’s something that should never have to become a part of your day-to-day life. In this blog post, we will show you how to change your ignition switch in just a few easy steps. You’ll be able to do this without any tools, and you’ll be one step closer to avoiding any car troubles in the future.
How to Change Ignition Switch In Car
If you’ve ever had to change the ignition switch on a car, you know it’s not an easy task. The good news is that it’s usually a pretty straightforward process, and most cars have very similar steps. Here’s everything you need to know:
1. Locate the ignition key. In most cases, this will be a small key that’s located under the driver side dashboard or in the console. If your car doesn’t have a keyhole, you may need to remove the dashboard or console cover.
2. Remove the old ignition switch. This can be done by gently prying it loose with a screwdriver or wrench, or by pulling it out from the housing completely. Try not to lose any of the screws that hold it in place!
3. Install the new ignition switch. Line up the screw holes on the new switch with those on the housing, and use screws to fasten it in place. Make sure that all of the wires going into and out of the switch are connected properly; if they’re not, you’ll have to replace them as well. Replace any other broken pieces before finally putting everything back together!
Things to Keep In Mind While Changing Ignition Switch
If you’ve ever had to change a car ignition switch, you know that it’s not an easy task. Here are some things to keep in mind while doing so.
1. Check the wiring. Sometimes the ignition switch can be replaced without removing any other components, by simply unplugging the old switch and plugging in the new one. If there is any significant damage to the wiring, however, it will likely require more extensive work.
2. Remove any obstructions. Before starting to remove the old switch, make sure there are no pieces of debris or anything else obstructing your view of the wiring connections beneath it.
3. Disconnect all electrical connectors. Once you’ve cleared away all obstacles and determined that the wiring is clear, disconnect all electrical connectors from the old switch and from each other. Make sure to label each connection as you go so that you can reattach them in the correct order once your new switch is installed.
4. Remove the old switch. To remove the old switch, first unscrew its mounting screws (usually four in total) using a Phillips head screwdriver。Once these screws have been removed, gently pull on the switch itself until it comes free from its mount
Change Ignition Switch Procedure in a Car
If your car’s ignition switch is sticking or not working correctly, there are a few simple steps you can take to fix the issue. The first thing you’ll want to do is inspect the switch for any obvious damage. If there is none, then you can try to reset it by pressing and holding both the on and off buttons at the same time for about 10 seconds. If that doesn’t work, you’ll need to replace the ignition switch.
Conclusion
If your car won’t start, there is a very good chance that the ignition switch is defective. Thankfully, changing the ignition switch is a relatively easy task that can be completed by just about anyone with some basic skills and tools. Before you begin, make sure to gather all of the necessary materials: a Phillips head screwdriver, an adjustable wrench, and a rag or cloth to protect your hands. Once you have everything you need, follow these simple steps: 1. Open the hood of your car and locate the power steering pump pulley (it will likely be attached to one of the engine mounts). 2. Disconnect the power steering line from this pulley by loosening the two screws on either side of it. 3. Next, remove both bolts that secure the power steering pump pulley to the engine mount. 4. Carefully lift up on the power steering pump Pulley assembly and set it aside in a safe place. 5 . Remove both screws from underneath the ignition switch cover plate (located at drivers side front corner of vehicle). This will allow you access to Torx T-20 driver needed to unscrew button – please see below image for more details: Note: Keep