If you own a car, there’s a good chance that you’ve encountered a power steering pump at some point. These small devices work by using centrifugal force to move the fluid in the engine, which in turn allows the car to stay straight and maneuver around corners easily. In this article, we’re going to take a closer look at how power steering pumps work and what you need to do to install them on your car. By the end, you’ll be able to put one in yourself with little effort!
Requirements for Putting A Power Steering Pump in
To put in a power steering pump, you’ll need the following:
1. A power steering pump
2. A power steering line
3. A power steering pump sealant
4. A power steering pump adapter
5. A power steering pump installation tool
6. A hydraulic jack
7. A hydraulic bucket
8. Lubricant (such as grease)
9. Supplies for re-sealing the lines (e.g., clamps, wire cutters)
10. Torque wrench and ratchet set
Tools You’ll Need
To put in a power steering pump, you’ll need the following tools:
-A floor jack and related stands
-A lug wrench (or bull bar)
-A breaker bar
-A power steering hose
-An air compressor
-A ratchet and socket set
– A bucket
– A cleaning cloth
Preparing The Area
You will need the following items to prepare for installing a power steering pump:
-A power steering pump
-A new or used power steering hoses
-New or used power steering belt
-New or used power steering pulleys
-A new or used belt guide
-New or used idler pulley
-New or used engine mount
-New or used torque converter mount (if equipped)
-New or used drive shaft (if equipped)
-New or used front wheel bearing (if applicable)
– New or used rear wheel bearing (if applicable)
– New or used circlip bolts and washers
– Some type of wrench, socket, and ratchet set
– A bucket
If your car has an automatic transmission, you will also need to get a torque converter lock ring tool.
Installing The Pump
First and foremost, before you install the pump, make sure all of your wiring is correct. You don’t want to damage anything while you’re trying to fix something that isn’t broken.
If your car has a manual steering system, you’ll need to disconnect the cables from the rack and pinion. If your car has a power steering system, simply pull the pump out of the reservoir. Now’s a good time to check your hoses for leaks.
There are three ways to install the pump: using a mounting bracket, using the mounting bracket with a tube adapter, or using the pump directly in the reservoir. We recommend using the mounting bracket with a tube adapter because it makes removal and installation much easier.
To install the mounting bracket with a tube adapter, first remove the old bracket by unscrewing it. Then use the supplied wrench to tighten down the adapter onto the pump shaft. Finally, screw on the new bracket and reattach any necessary hoses.
If installing in direct in reservoir mode, first remove any coverings from around the reservoir opening. This includes any bumper or trim pieces as well as any plastic or rubber sealant that might have been put in place to contain moisture or dust
Tips For Making Your Pump Installation A Success
Pumping your power steering system is one of those maintenance tasks that can seem daunting, but with the right tools and a bit of know-how, it can be a breeze. Here are some tips to make your pump installation a success.
1. Check the Compatibility of Your Pump
Before you start buying parts, first make sure your pump is compatible with your car. Many pumps are available in universal versions that work with many makes and models of cars, but there may be specific requirements for your car’s power steering system. Find out what type of pump you need and buy it beforehand, so you don’t have to worry about compatibility issues during installation.
2. Prepare Your Drain Pan
Before you start pumping fluid, drain any excess fluid from your power steering system. This will help prevent damage to the system while you install the pump. Make sure the drain pan is large enough to catch all the fluid, and place it where it will be easily accessible.
3. Get The Right Tools For The Job
You’ll need a few basic tools for installing a power steering pump: a wrench set and an armful of zip ties. You’ll also want Needle Nosed Pliers for removing clips and fittings