There are a few steps you need to take in order to remove your power steering pump reservoir. The first is to remove the bolts that hold it in place. Once these are removed, you can then detach the reservoir from the pump by gently pulling on each end. Be careful not to damage the reservoir in any way.
Location of power steering pump reservoir
If you’re experiencing loss of power steering, it’s likely that the reservoir has been depleted. This is a common issue with older vehicles, and can be difficult to diagnose. In this tutorial, we’ll show you how to locate and remove the reservoir on a 2007-2017 GM Cruze.
Start by turning the car off and removing the key. Next, you’ll need to remove the air intake grille cover. On some models, this may require disconnecting the battery cables as well. Once the cover is off, you’ll see the engine coolant system on your left side. On some models, you’ll also see the power steering pump inlet on your right side.
To access the reservoir, first unscrew the two screws that hold it in place (you may need a philips head screwdriver). Once those screws are out, gently pull out the reservoir. Make sure to replace it if it’s damaged or missing any parts. Replace everything and re-secure with screws once you’re done.
Removal procedure
If you have to remove the power steering pump reservoir, it is best to do it in a carefully planned sequence.
1. Close off all the access points to the engine bay. This includes the air intake, fuel lines, and anything else that could leak fluid or sparks.
2. Drain any fluid that may be in the reservoir using a turkey baster or q-tip. Discard any fluid that is cloudy or brownish in color.
3. Remove the four bolts that hold the reservoir cover on. Be careful not to damage the plastic seal around the plug hole when removing the cover.
4. Carefully lift off the cover and locate the piston and cylinder assemblies. Use a socket wrench to unscrew them from the housing. Save the seals and o-rings for later replacements.
5. Disconnect both hoses from the unit and let them drain into a container. Be sure to label both ends of each hose so you can reattach them in reverse order later on.
6. Remove the three screws that hold the pressure regulator in place and gently remove it from the housing. Save all of its seals, o-rings, and clips for later replacement.
7
Wiping down the area before replacement
If you are reading this, it is likely that your power steering pump has gone out and you need to replace it. Before you do anything else, make sure to clean the area down where the pump will be installed. This will help eliminate any debris that may cause problems later on.
Once the area is clean, you can start to replace the pump. Make sure to use a properly fitting sealant on the threads of the pump so it will not leak. And finally, make sure to tighten everything down properly once installation is complete.
Removal of the power steering pump reservoir
There are a few steps involved in removing the power steering pump reservoir. This guide will outline the required tools and knowledge needed for this task.
Required Tools:
– Phillips head screwdriver
– Wrench or torque wrench
– Flathead screwdriver
-Socket set
– Hammer
– Nylon ratchet strap
Optional Tools:
– Channel locks (for securing the reservoir)
– JB Weld (for repairing leaks)
The first step is to remove the screws that hold the reservoir cover on. There are six in all, three on each side. Once these screws are removed, gently pry the cover off of the reservoir. Make sure to keep track of the orientation of the reservoir while doing so, as you will need it when reinstalling it. Once the cover is off, you will see the two HPI ball valves that control the flow of fluid into and out of the pump. These valves should be replaced as part of any power steering system overhaul, so don’t damage them during this removal process. You will also see two hoses connected to the pump – one goes down into the reservoir and one goes up to the housing where the pump is mounted. The
Replacing the power steering pump reservoir
If you’re like most drivers, you’ve probably had to replace your power steering pump reservoir at least once in your car’s lifetime. And if you’re like most drivers, you probably don’t know how to do it yourself.
The reservoir is a small, plastic component located behind the power steering pump on most cars. It holds the fluid that helps turn the pump’s gears, and over time it can get clogged with debris and oil. When this happens, your car will start to feel weak and difficult to drive.
Replacing the reservoir is a fairly simple job, but it can be tricky if you don’t know what you’re doing. Here are step-by-step instructions on how to do it:
1) Disconnect the battery cable and the air conditioning compressor connector. These connectors are usually mounted under the hood on the passenger side or under the dash on the driver side.
2) Remove the cover plate over the power steering pump relay box. This is usually accessible through a hole in the firewall (the metal enclosure that separates the engine from the passenger compartment). Pry it off with a flathead screwdriver.
3) Remove the four screws that hold down the power steering pump relay box