How To Replace Ignition Lock Cylinder On Chrysler K Car

If you’re like most drivers, chances are you’ve experienced a problem with your ignition lock at some point. In fact, the National Highway Traffic Safety Administration (NHTSA) reports that about 1 in 5 car owners have to deal with an ignition lock issue in their lifetime. If you’re experiencing problems with your ignition lock and are not sure how to fix it, read on for a step-by-step guide on how to replace the cylinder. You may be surprised at just how easy it is!

What is an Ignition Lock Cylinder?

An ignition lock cylinder is a small cylinder that sits in the keyway of your car’s ignition. It’s used to secure the key in the “on” position and is responsible for preventing unauthorized access to your vehicle. If this cylinder becomes damaged, it can prevent your car from starting.

What Do I Do If My Ignition Lock Cylinder Is Broken?

If you have a Chrysler K car, your ignition lock cylinder may be broken. This means that the car cannot be started without using the key. If your ignition lock cylinder is broken, you will need to replace it. Here are steps on how to do this:

1. Park your car in a safe place.

2. Disable the security system by turning off the key and removing the battery if present.

3. Open the hood of your car and locate the fuse box. Find and disable the fuse for the “Ignition” module. This will allow you to bypass the security system and start your car.

4. Remove the screws that hold down the ignition lock cylinder cover panel on either side of the engine bay (see image). Be careful not to damage any wires or cables connected to it!

5. Carefully remove both ignition lock cylinder covers (see image). Be sure to save both of them! You will need them later when replacing your cylinder.

6. Locate and remove the broken ignition lock cylinder from your car (see image). Save all of its parts for later disposal! If necessary, use a Phillips head screwdriver to unscrew and remove the broken pieces from

See also  What Does Msd Ignition Do To Your Car

How to Replace an Ignition Lock Cylinder on a Chrysler K Car

If your Chrysler K car’s ignition lock cylinder needs replacement, there are a few things you’ll need before getting started. The first is a tool that fits the original cylinder’s dimensions, such as a hex bit screwdriver or a special cylinder removal tool. Second, you’ll need to remove the old cylinder. Fourth, insert the new cylinder and secure it in place with the appropriate screws. Fifth, replace the panel that covers the engine and ignition switch. Finally, reattach any wires and connectors needed and you’re ready to go!

Final Thoughts

If your Chrysler K car has a broken ignition lock cylinder, you will need to replace it. This is a fairly simple procedure that can be done with a few tools and some basic knowledge about cars. Here are the steps:

1. Remove the front bumper cover. The cover is held on by four screws at the front edge of the car. Once it is removed, you will see two air ducts in the center of the bumper cover.
2. Position a towel under one of the ducts and use a vacuum cleaner to remove any dirt or dust from around the ignition lock cylinder hole. You can also use an electric drill if necessary to make sure there are no obstructions in this area.
3. If you have access to an impact tool, you can use it to break open the old ignition lock cylinder casing. Be careful not to damage the wires inside! If you don’t have access to an impact tool, you can try using a screwdriver or knife to pry open the casing (be very careful not to cut yourself).
4. Once open, insert a new ignition lock cylinder into the hole and snap it into place by pressing down on all sides of the casing until it snaps into place

DynoCar is the best place to find information on all things cars, whether it be a car buying guide or how to change your oil. We’ve made finding and staying in touch with car information easy and fast.

Resources

Guides

About Us

Contact

Contact

DynoCar - All About Cars

(440) 999 3699

590 Monterey Blvd San Francisco, CA 94127

Information contained herein is for informational purposes only, and that you should consult with a qualified mechanic or other professional to verify the accuracy of any information. DynoCar.org shall not be liable for any informational error or for any action taken in reliance on information contained herein.