When it comes to automotive repairs, most people know that they should always replace the oil, air filter, spark plugs, and tire pressure monitoring system (TPMS) sensor when they rotate their tires. But what about the power steering pump? On 2010 Chevy Traverse models, the power steering pump is located in the engine bay and needs to be replaced as part of a routine maintenance schedule. If you don’t replace it when your car’s time for an overhaul, you could find yourself struggling with a loss of power and difficulty steering. Here are instructions on how to replace the power steering pump on a 2010 Chevy Traverse: 1. Disable the car’s traction control system by pressing and holding down both the brake pedal and the gas pedal simultaneously. 2. Open the hood and locate the battery. Disconnect the negative terminal from it and then unscrew the cap on top of the radiator. Note: The fan housing should also be removed at this point if it exists; see photos later in this article for clarification. 3. Remove two screws from behind the battery cover, then gently pull it forward so that it hangs down by its cables. Loosen two more screws at this point, then pull forward on both
Identification of the Part Needed
If you are wondering how to replace the power steering pump on a Chevy Traverse, here is a list of the parts you will need:
-Power steering pump
-Piston
– hydraulic line
– reservoir
– Pressure regulator
– Hose clamp
– Adapter
– Torque wrench
– Ratchet and socket set
– Fluid.
1. Identification of the Part Needed: The first step is to identify which part needs to be replaced. The power steering pump is usually located near the engine and can be identified by its size and shape. The piston will also be different in shape, as it needs to fit tightly inside the pump. The hydraulic line and reservoir are also important parts and can sometimes be difficult to find. Once you have identified the part needed, proceed to step 2.
2. Replacement of the Part Needed: Next, remove the old part from your Chevy Traverse by following the instructions that came with your replacement part. Make sure to use the appropriate tools for the job, as indicated in step 3. Once the old part has been removed, install the new one using the same instructions. Finally, replace any components that were replaced during installation, such as the pressure regulator
Removal and Replacement Procedure
1. To replace the power steering pump on a Chevy Traverse, follow these steps:
a. Open the hood and remove the front bumper, then the front grille.
b. Remove the left front wheel.
c. Disconnect the power steering hose from the pump housing by unscrewing it.
d. Lift off the pump housing and remove the pump.
e. Install the new pump by following steps a-d, reattach the power steering hose, and reinstall the wheel, bumper, and grille.
Wiring Connections
1. To replace the power steering pump on a Chevy Traverse, you will need to remove the front fascia. The front fascia is a plastic cover that covers the engine, drivetrain, and radiator.
2. To remove the front fascia, you will need to disconnect the negative battery cable and then remove two screws that hold the fascia in place.
3. Once the fascia is loose, use a socket wrench to unscrew the bolts that hold the pump in place. Be careful not to lose any of the parts that are attached to the pump.
4. Remove the pump and replace it with a new one. Make sure to reconnect all of the wiring connections before reinstalling the fascia.
Replacement Pump
To replace the power steering pump on a Chevy Traverse, start by draining the fluid from the reservoir.
Next, remove the screws that hold the bracket in place and lift it off. Then, use a wrench to unscrew the power steering pump from the shaft. Once it is free, replace the pump with a new one and reattach the bracket.
Finally, refill the reservoir with new fluid and screw the reservoir back onto the pump.
Testing the Pump Operation
To replace the power steering pump on a Chevy Traverse, you first need to test the pump operation. To do this, turn the wheel all the way to the left and all the way to the right. If the car moves in a straight line, the power steering pump is working properly. If it moves erratically or pulls to one side, the pump may need to be replaced.
Conclusion
If your 2010 Chevy Traverse is experiencing Issues with power steering, it might be time to replace the pump. This guide will show you how to do just that and give you some tips on how to keep the replacement as simple and trouble-free as possible. Have fun!