Anyone who owns a car knows that power steering is an important part of making sure the vehicle runs smoothly. But what happens when there’s something wrong with the power steering pump? In this article, we’ll show you how to take the reservoir off your power steering pump so that you can fix any issues!
What You Will Need
In order to take your reservoir off the power steering pump, you will need a few tools. Firstly, you will need a ratchet and a socket that fit the power steering pump nut. Secondly, you will need a flat head screwdriver. Lastly, you will need pliers.
Taking your reservoir off the power steering pump is not a difficult task, but it is important to follow the steps carefully. If you are not careful, you could damage the power steering pump or the reservoir itself.
1. First, use the ratchet and socket to loosen the power steering pump nut. Do not remove the nut completely, just loosen it enough so that you can remove the reservoir.
2. Next, use the flat head screwdriver to pry the reservoir off the power steering pump. Be careful not to damage the pump as you do this.
3. Finally, use the pliers to remove the O-ring from the power steering pump port. This will prevent any leaks when you put the new reservoir on.
Step One – Remove the Negative Battery Cable
Start by removing the negative battery cable from the battery. This will help to prevent any electrical shorts while you are working on the power steering pump.
Step Two – Disconnect the Power Steering Pump
Once the negative battery cable is removed, you can then disconnect the power steering pump from the vehicle. There are typically two bolts that hold the pump in place. These bolts will need to be removed in order to take the pump off of the vehicle.
Step Three – Remove the Reservoir from the Pump
The reservoir is located on top of the power steering pump. In order to remove it, you will need to unscrew the cap that is holding it in place. Once the cap is removed, you can then carefully pull the reservoir away from the pump. Be careful not to damage any of the hoses or connections.
Step Four – Clean and inspect all components
Once the reservoir is removed, take a moment to clean all of the components. Inspect them for any wear or damage. If any of the parts are damaged, they will need to be replaced before reassembly.
Step Five – Reattach the Reservoir and Replace The Cap
Carefully reattach the reservoir to the
Step Two – Disconnect the Power Steering Pump Pressure Line
Now that the power steering pump is free from the reservoir, you can disconnect the pressure line. This is usually a simple matter of unscrewing a retaining clip or bolt and then slipping the pressure line off the pump. You may need to use a pick or small screwdriver to help separate the line from the pump, but be careful not to damage either the line or the pump. Once the pressure line is disconnected, you can remove the power steering pump from your vehicle.
Step Three – Remove the Power Steering Pump Bolts
Now that the pressure line is disconnected, you can remove the bolts holding the power steering pump to the engine. There are typically two or three bolts, depending on your vehicle. Remove these bolts and set the power steering pump aside.
Step Four – Remove the Power Steering Pump Pulley
1. Using a power steering pulley Removal tool, remove the power steering pump pulley from the shaft of the pump.
2. Remove the retaining nut from the back of the pulley using a wrench.
3. Pull the pulley off of the shaft.
4. Inspect the surfaces of the shaft and pulley for any damage or wear. Replace if necessary.
Step Five – Install the New Power Steering Pump
If you’re installing a new power steering pump, the process is similar to taking the old one off. Begin by disconnecting the negative battery cable, then loosen the belt that goes to the power steering pump so you can remove it. Next, use a wrench or socket to loosen the bolts that hold the power steering pump in place, and carefully remove it.Now, take your new power steering pump and line it up with the mounting holes on the engine. Once it’s in place, hand-tighten the bolts to hold it in place, then use a wrench or socket to finish tightening them. Finally, reconnect the power steering pump belt and reattach the negative battery cable.
Step Six – Reconnect the Power Steering Pump Pressure Line
Now that the reservoir is off the power steering pump, it’s time to reconnect the pressure line. This is a simple process, but be careful not to over-tighten the connection, as this can damage the line. Once the pressure line is reconnected, your power steering system will be back up and running!
Step Seven – Reinstall the Power
Now that you have successfully removed the reservoir from the power steering pump, it is time to reinstall it. Begin by reconnecting the hoses to the ports on the reservoir. Once the hoses are secure, position the reservoir into place and bolt it down. Make sure that the reservoir is securely fastened before moving on to the next step.