Have you ever been out of town and needed to get your car started but couldn’t figure out how to do it? Chances are, if you’re like most people, you’ve tried every possible combination of buttons, levers, and wires that you could think of. Unfortunately, this can be a pretty frustrating experience – especially if you’re trying to do it in a hurry.
Fortunately, there’s an easier way to get your car going – with the help of a mechanic! But before you can take advantage of their services, you’ll need to know how to unlock a car engine. This simple procedure can save you time and hassle in the future, so make sure you know how to do it before your next trip out of town!
Start by turning off the engine
Next, use a flat head screwdriver to pry the cover above the engine bay away from the car. There are usually two Phillips head screws on each side.
Now remove the four bolts that hold the cover in place. Be careful not to lose any of the screws. You’ll need them later.
Once the cover is free, slide it towards the passenger side of the car. There’s a small light attached to it, so be sure to unplug it before moving the cover.
Now you’ll need to remove the six screws that secure the engine block to the chassis. Again, be careful not to lose any of these screws. They’re very important! Once they’re out, gently pull the engine block out of its mounting bracket and set it aside.
You’ll also notice a couple of oil coolers attached to the engine block – you can remove them if you want. Just be careful not to lose any of the clips that secure them in place. Once they’re free, gently pull them off and set them aside as well.
Now you can take a look at the motor itself. There are usually three electrical connectors attached:
Check the oil level and add more if needed
How to unlock a car engine:
If your car has a keyless entry system, you’ll need to first unlock the glovebox. This is typically done by depressing a button on the door handle or inside the car. Next, locate the engine block security screw on the driver’s side and remove it with a Phillips head screwdriver. Be sure to keep the screws in order as you will need them later. Once the security screw is removed, use a flathead screwdriver to pry up on the engine cover at the front of the car. It should pop off easily once released. Gently pull it forward until it stops, then gently push it back down into place. Finally, reattach the engine cover using the screws that were removed earlier.
Locate the key
If you have a car with an engine immobilizer, you’ll need to find the key before you can start the engine. There are a few ways to locate the key:
– Look for a visible key in the car.
– Check under the car for a hidden keyhole.
– Look for a tag or sticker with the car’s VIN number that may list the key’s location.
Open the car door
1. Insert a key into the ignition.
2. Turn the key to the ‘On’ position.
3. Turn the car’s engine to ‘Start’, then turn it off again.
4. Turn the key to the ‘Off’ position and remove the key from the ignition.
5. Pry open the locking tab on one of the car door hinges with a flathead screwdriver (Photo 1).
6 . Open one of the car door panels (Photo 2).
7. Remove the security panel (if present) and disconnect the battery cable ( Photo 3 ).
8. Remove two screws that hold down a plastic cover ( Photo 4 ).
9. Lift up the cover and disconnect two wires ( Photo 5 ).
10. Disconnect two connectors at the back of the unlocking module using a screwdriver or a pair of pliers (Photo 6).
11. Remove the module by sliding it off towards the drivers side of the car (Photo 7).
12. Reattach any cables that you disconnected in Step 10 and replace any damaged components (Photo 8).
Put the car in park
1. Turn off the car
2. Locate the emergency brake button (usually on the center console)
3. Push and hold the emergency brake button until the car rolls to a stop
4. Turn off the car
5. Remove the key from the ignition
6. Insert a flathead screwdriver into the access hole near the battery (it’s usually in a black plastic housing) and twist it anticlockwise until it pops out of its socket
7. Keep holding down the emergency brake button as you unscrew the screws on the side of the housing and lift it off
8. Drop the key into a safe place
9. Pry open the hood and remove the engine cover (it has two clips at each end)
10. Lift up on the cover and pull it off
Now that you have access to your car’s engine, you’ll need to remove some protective components before you can start working. The first is the emergency brake lever, which you should push in until you hear a click to indicate that it’s in position — this will hold your car in place while you work. You’ll also need to disconnect both battery cables, although in most cases
Remove the ignition key
If you’ve ever been stranded on the side of the road with a locked car, you know how frustrating it can be. Fortunately, there are a few simple steps you can take to unlock a car engine without using the key.
To begin, remove the ignition key from the ignition. Next, use a flathead screwdriver to pry open the hood release handle. Finally, pull up on the hood release cable and lift it off of the hinges. Once the hood is open, you can access the engine Remote Start unit by removing the screws that hold it in place.
If your car has an immobilizer system, be sure to disable it before trying to unlock the engine. Most cars have a button or switch on the dashboard that you can use to disable the immobilizer system.
Lock the car door using the buttons on the remote
1. Press and hold the unlock button on the car remote for two seconds.
2. Release the unlock button and press the lock button on the car remote. The car’s engine should now be locked.
If the engine is not locked, repeat these steps.
Return to your house
If you find yourself locked out of your car, don’t panic! There are many ways to unlock a car engine remotely. One option is to use a key fob. If you have a newer car, you may be able to access the car’s computer system and unlock the engine using your smartphone. If your car doesn’t have a computer system, there are still several methods you can try.
One option is to use an emergency key. This type of key is specifically designed for emergencies and can be used without unlocking the car first. You can also try using a spare key that’s not registered to the vehicle. Finally, you can try using a code that’s specific to your car.